R/data.R
In jariou/MachCalc: A Machinist Calculator
## A table of tap drill sizes
## @docType and @name; do not forget NULL in the end
#' Starrett Inch Tap Drill Sizes
#'
#' A few numbers from \code{rnorm()}.
#' @docType data
#' @name StarrettTapDrills
#' @format A numeric data frame.
#' @source Generated from \code{
#' decimal <- c(
#' 0.0135, 0.0145, 0.0156, 0.0160, 0.0180, 0.0200,
#' 0.0210, 0.0225, 0.0240, 0.0250, 0.0260, 0.0280,
#' 0.0292, 0.0310, 0.0312, 0.0320, 0.0330, 0.0350,
#' 0.0360, 0.0370, 0.0380, 0.0390, 0.0400, 0.0410,
#' 0.0420, 0.0430, 0.0465, 0.0469, 0.0520, 0.0550,
#' 0.0595, 0.0625, 0.0635, 0.0670, 0.0700, 0.0730,
#' 0.0760, 0.0781, 0.0785, 0.0810, 0.0820, 0.0860,
#' 0.0890, 0.0935, 0.0938, 0.0960, 0.0980, 0.0995,
#' 0.1015, 0.1040, 0.1065, 0.1094, 0.1100, 0.1110,
#' 0.1130, 0.1160, 0.1200, 0.1250, 0.1285, 0.1360,
#' 0.1405, 0.1406, 0.1440, 0.1470, 0.1495, 0.1520,
#' 0.1540, 0.1562, 0.1570, 0.1590, 0.1610, 0.1660,
#' 0.1695, 0.1719, 0.1730, 0.1770, 0.1800, 0.1820,
#' 0.1850, 0.1875, 0.1890, 0.1910, 0.1935, 0.1960,
#' 0.1990, 0.2010, 0.2031, 0.2040, 0.2055, 0.2090,
#' 0.2130, 0.2188, 0.2210, 0.2280, 0.2340, 0.2344,
#' 0.2380, 0.2420, 0.2460, 0.2500, 0.2570, 0.2610,
#' 0.2656, 0.2660, 0.2720, 0.2770, 0.2810, 0.2812,
#' 0.2900, 0.2950, 0.2969, 0.3020, 0.3125, 0.3160,
#' 0.3230, 0.3281, 0.3320, 0.3390, 0.3438, 0.3480,
#' 0.3580, 0.3594, 0.3680, 0.3750, 0.3770, 0.3680,
#' 0.3906, 0.3970, 0.4040, 0.4062, 0.4130, 0.4219,
#' 0.4375, 0.4531, 0.4688, 0.4844, 0.5000, 0.5156,
#' 0.5312, 0.5469, 0.5625, 0.5781, 0.5938, 0.6094,
#' 0.6250, 0.6406, 0.6562, 0.6719, 0.6875, 0.7031,
#' 0.7188, 0.7344, 0.7500, 0.7656, 0.7812, 0.7969,
#' 0.8125, 0.8281, 0.8438, 0.8594, 0.8750, 0.8906,
#' 0.9062, 0.9219, 0.9375, 0.9531, 0.9688, 0.9844,
#' 1.0000, 1.0469, 1.1094, 1.1250, 1.1719, 1.2188,
#' 1.2500, 1.2969, 1.3438, 1.3750, 1.4219, 1.5000
#' )
#' drills <- (
#' 80 , 79 , 1/64 , 78 , 77 , 76,
#' 75 , 74 , 73 , 72 , 71 , 70,
#' 69 , 68 , 1/32 , 67 , 66 , 65,
#' 64 , 63 , 62 , 61 , 60 , 59,
#' 58 , 57 , 56 , 3/64 , 55 , 54,
#' 53 , 1/16 , 52 , 51 , 50 , 49,
#' 48 , 5/64 , 47 , 46 , 45 , 44,
#' 43 , 42 , 3/32 , 41 , 40 , 39,
#' 38 , 37 , 36 , 7/64 , 35 , 34,
#' 33 , 32 , 31 , 1/8 , 30 , 29,
#' 28 , 9/64 , 27 , 26 , 25 , 24,
#' 23 , 5/32 , 22 , 21 , 20 , 19,
#' 18 , 11/64 , 17 , 16 , 15 , 14,
#' 13 , 3/16 , 12 , 11 , 10 , 9,
#' 8 , 7 , 13/64 , 6 , 5 , 4,
#' 3 , 7/32 , 2 , 1 , A , 15/64,
#' B , C , D , 1/4 E, F , G,
#' 17/64 , H , I , J , K , 9/32,
#' L , M , 19/64 , N , 5/16 , O,
#' P , 21/64 , Q , R , 11/32 , S,
#' T , 23/64 , U , 3/8 , V , W,
#' 25/64 , X , Y , 13/32, Z , 27/64,
#' 7/16 , 29/64 , 15/32 , 31/64, 1/2 , 33/64,
#' 17/32 , 35/64 , 9/16 , 37/64, 19/32 , 39/64,
#' 5/8 , 41/64 , 21/32 , 43/64, 11/16 , 45/64,
#' 23/32 , 47/64 , 3/4 , 49/64, 25/32 , 51/64,
#' 13/16 , 53/64 , 27/32 , 55/64, 7/8 , 57/64,
#' 29/32 , 59/64 , 15/16 , 61/64, 31/32 , 63/64,
#' 1 , 1 3/64 , 1 7/64 , 1 1/8, 1 11/64, 1 7/32,
#' 1 1/4 , 1 19/64, 1 11/32, 1 3/8, 1 27/64, 1 1/2
#' )
#' TapSizeInch <- c(
#' , , , , , ,
#' , , , , , ,
#' , , , , , ,
#' , , , , , ,
#' , , , "0-80" , , ,
#' "1-64,1-72", , , , "2-56,2-64", ,
#' , , "3-48" , , "3-56" , ,
#' "4-40" , "4-48" , , , , ,
#' "5-40" , "5-44" , "6-32" , , , 0.1110 ,
#' "6-40" , , , , , "8-32,8-36",
#' , , , , "10-24" , 0.1520 ,
#' , , , "10-32" , , ,
#' , , , "12-24" , , "12-28" ,
#' , , , , , ,
#' , "1/4-20" , , , , ,
#' "1/4-28" , , , , , ,
#' , , , , "5/16-18" , ,
#' , , "5/16-24" , , , ,
#' , , , , "3/8-16" , ,
#' , , "3/8-24" , , , ,
#' , , "7/16-14" , , , ,
#' "7/16-20" , , , , , "1/2-13" ,
#' , "1/2-20" , , "9/16-12" , , "9/16-18" ,
#' "5/8-11" , , , "5/8-18" , , ,
#' , , "3/4-10" , , "3/4-16" , ,
#' , , , "7/8-9" , , ,
#' "7/8-14" , , , , "1-8" , ,
#' , "1-12" , "1-14" , , , "1 1/8-7" ,
#' , "1 1/8-12", "1 1/4-7" , , "1 1/4-12" , "1 3/8-6" ,
#' , "1 3/8-12", "1 1/2-6" , , "1 1/2-12" ,
#' )
#' InchTapDrills <- data.frame(Decimal,
#' Drills,
#' inchTapSize,
#' stringsAsFactors = FALSE)
#' }
#' @examples data(InchTapDrills)
#' str(InchTapDrills)
NULL
#' Starrett Metric Tap Drill Sizes
#'
#' A few numbers from \code{rnorm()}.
#' @docType data
#' @name MetricTapDrills
#' @format A numeric data frame.
#' @source Generated from \code{
#' ThreadSizeMetric <- c(
#' 1.6, 1.8, 2 , 2.2, 2.5, 3,
#' 3.5, 4 , 4.5, 5 , 6 , 7,
#' 8 , 8 , 10 , 10 , 12 , 12,
#' 14 , 14 , 16 , 16 , 18 , 18,
#' 20 , 20 , 22 , 22 , 24 , 24,
#' 27 , 27 , 30 , 30 , 33 , 33,
#' 36 , 36 , 39 , 39
#' )
#' ThreadPitchMeric <- (
#' 0.35, 0.35, 0.4 , 0.45, 0.45, 0.5 ,
#' 0.6 , 0.7 , 0.75, 0.8 , 1 , 1 ,
#' 1.25, 1 , 1.5 , 1.25, 1.75, 1.25,
#' 2 , 1.5 , 2 , 1.5 , 2.5 , 1.5 ,
#' 2.5 , 1.5 , 2.5 , 1.5 , 3 , 2 ,
#' 3 , 2 , 3.5 , 2 , 3.5, 2 ,
#' 4 , 3 , 4 , 3
#' )
#' TapDrillMetric <- (
#' 1.25, 1.45, 1.60, 1.75, 2.05, 2.50,
#' 2.90, 3.30, 3.70, 4.20, 5.00, 6.00,
#' 6.70, 7.00, 8.50, 8.70, 10.20, 10.80,
#' 12.00, 12.50, 14.00, 14.50, 15.50, 16.50,
#' 17.50, 18.50, 19.50, 20.50, 21.00, 22.00,
#' 24.00, 25.00, 26.50, 28.00, 29.50, 31.00,
#' 32.00, 33.00, 35.00, 36.00
#' )
#' TapDrillInch <- c(
#' 0.0492, 0.0571, 0.0630, 0.0689, 0.0807, 0.0984,
#' 0.1142, 0.1299, 0.1457, 0.1654, 0.1968, 0.2362,
#' 0.2638, 0.2756, 0.3346, 0.3425, 0.4016, 0.4252,
#' 0.4724, 0.4921, 0.5512, 0.5709, 0.6102, 0.6496,
#' 0.6890, 0.7283, 0.7677, 0.8071, 0.8268, 0.8661,
#' 0.9449, 0.9843, 1.0433, 1.1024, 1.1614, 1.2205,
#' 1.2598, 1.2992, 1.3780, 1.4173
#' )
#' MetricTapDrills <- data.frame(ThreadSizeMetric,
#' ThreadPitchMetric,
#' TapDrillMetric,
#' TapDrillInch,
#' stringsAsFactors = FALSE)
#' }
#' @examples data(InchTapDrills)
#' str(InchTapDrills)
NULL
#' Starrett Pipe Thread Tap Drill Sizes
#'
#' A few numbers from \code{rnorm()}.
#' @docType data
#' @name StarrettTapDrills
#' @format A numeric data frame.
#' @source Generated from \code{
#' DrillSize <- (
#' 11/32, 7/16 , 37/64, 23/32 , 59/64 , 1 5/32, 1 1/2,
#' 1 3/4, 2 7/32, 2 21/32, 3 1/4, 3 3/4, 4 1/4
#' )
#' ThreadSize <- c(
#' "1/8" , "1/4", "3/8" , "1/2", "3/4" , "1", "1 1/4",
#' "1 1/2", "2" , "2 1/2", "3" , "3 1/2", "4"
#' )
#' ThreadPitch <- c(
#' 27 , 18, 18 , 14, 14 , 11.5, 11.5,
#' 11.5, 11.5 , 8, 8 , 8, 8
#' )
#' PipeThreadDrill <- data.frame(Decimal,
#' Drills,
#' inchTapSize,
#' stringsAsFactors = FALSE)
#' }
#' @examples data(PipeThreadDrill)
#' str(PipeThreadDrill)
NULL
#' Cutting Speeds Table
#'
#' Cutting speeds for various materials
#' using a plain high speed steel cutter
#' @docType data
#' @name CuttingSpeeds
#' @format A numeric data frame.
#' @source Generated from \code{
#' Material <- c( "Steel (tough)",
#' "Mild Steel",
#' "Mild Steel (with colant)",
#' "Cast Iron",
#' "Alloy Steels (1320–9262)",
#' "Carbon Steels (C1008–C1095)",
#' "Free Cutting Steels (B1111–B1113 & C1108–C1213)",
#' "Stainless Steels (300 & 400 series)",
#' "Bronzes",
#' "Steel 12L14",
#' "Aluminium",
#' "Brass",
#' "Machinable Wax",
#' "Delrin",
#' "Polyethylene",
#' "Acrylic (with coolant)",
#' "Wood"
#' )
#' MPM.Min <- c(18, 3, 6, 1, 3, 4, 35, 23, 24, 9, 122, 90, 6, 11, 12, 15, 183)
#' MPM.Max <- c(50, 38, 7, 2, 20, 21, 69, 40, 45, 10, 305, 210, 6, 11, 12, 15, 305)
#' SFM.Min <- c(60, 10, 20, 6, 12, 10, 115, 30, 10, 30, 400, 300, 20, 35, 40, 50, 600)
#' SFM.Max <- c(100, 125, 25, 8, 65, 70, 225, 7, 80, 33, 1000, 700, 20, 35, 40, 50, 1000)
#'
#' cuttingSpeeds <- data.frame(Material, MPM.Min, MPM.Max, SFM.Min, SFM.Max, stringsAsFactors = FALSE)
#' }
#' @examples data(cuttingSpeeds)
#' str(cuttingSpeeds)
NULL
jariou/MachCalc documentation built on March 1, 2020, 2:38 a.m.
R Package Documentation
Browse R Packages
We want your feedback!
Note that we can't provide technical support on individual packages. You should contact the package authors for that.
## A table of tap drill sizes
## @docType and @name; do not forget NULL in the end
#' Starrett Inch Tap Drill Sizes
#'
#' A few numbers from \code{rnorm()}.
#' @docType data
#' @name StarrettTapDrills
#' @format A numeric data frame.
#' @source Generated from \code{
#' decimal <- c(
#' 0.0135, 0.0145, 0.0156, 0.0160, 0.0180, 0.0200,
#' 0.0210, 0.0225, 0.0240, 0.0250, 0.0260, 0.0280,
#' 0.0292, 0.0310, 0.0312, 0.0320, 0.0330, 0.0350,
#' 0.0360, 0.0370, 0.0380, 0.0390, 0.0400, 0.0410,
#' 0.0420, 0.0430, 0.0465, 0.0469, 0.0520, 0.0550,
#' 0.0595, 0.0625, 0.0635, 0.0670, 0.0700, 0.0730,
#' 0.0760, 0.0781, 0.0785, 0.0810, 0.0820, 0.0860,
#' 0.0890, 0.0935, 0.0938, 0.0960, 0.0980, 0.0995,
#' 0.1015, 0.1040, 0.1065, 0.1094, 0.1100, 0.1110,
#' 0.1130, 0.1160, 0.1200, 0.1250, 0.1285, 0.1360,
#' 0.1405, 0.1406, 0.1440, 0.1470, 0.1495, 0.1520,
#' 0.1540, 0.1562, 0.1570, 0.1590, 0.1610, 0.1660,
#' 0.1695, 0.1719, 0.1730, 0.1770, 0.1800, 0.1820,
#' 0.1850, 0.1875, 0.1890, 0.1910, 0.1935, 0.1960,
#' 0.1990, 0.2010, 0.2031, 0.2040, 0.2055, 0.2090,
#' 0.2130, 0.2188, 0.2210, 0.2280, 0.2340, 0.2344,
#' 0.2380, 0.2420, 0.2460, 0.2500, 0.2570, 0.2610,
#' 0.2656, 0.2660, 0.2720, 0.2770, 0.2810, 0.2812,
#' 0.2900, 0.2950, 0.2969, 0.3020, 0.3125, 0.3160,
#' 0.3230, 0.3281, 0.3320, 0.3390, 0.3438, 0.3480,
#' 0.3580, 0.3594, 0.3680, 0.3750, 0.3770, 0.3680,
#' 0.3906, 0.3970, 0.4040, 0.4062, 0.4130, 0.4219,
#' 0.4375, 0.4531, 0.4688, 0.4844, 0.5000, 0.5156,
#' 0.5312, 0.5469, 0.5625, 0.5781, 0.5938, 0.6094,
#' 0.6250, 0.6406, 0.6562, 0.6719, 0.6875, 0.7031,
#' 0.7188, 0.7344, 0.7500, 0.7656, 0.7812, 0.7969,
#' 0.8125, 0.8281, 0.8438, 0.8594, 0.8750, 0.8906,
#' 0.9062, 0.9219, 0.9375, 0.9531, 0.9688, 0.9844,
#' 1.0000, 1.0469, 1.1094, 1.1250, 1.1719, 1.2188,
#' 1.2500, 1.2969, 1.3438, 1.3750, 1.4219, 1.5000
#' )
#' drills <- (
#' 80 , 79 , 1/64 , 78 , 77 , 76,
#' 75 , 74 , 73 , 72 , 71 , 70,
#' 69 , 68 , 1/32 , 67 , 66 , 65,
#' 64 , 63 , 62 , 61 , 60 , 59,
#' 58 , 57 , 56 , 3/64 , 55 , 54,
#' 53 , 1/16 , 52 , 51 , 50 , 49,
#' 48 , 5/64 , 47 , 46 , 45 , 44,
#' 43 , 42 , 3/32 , 41 , 40 , 39,
#' 38 , 37 , 36 , 7/64 , 35 , 34,
#' 33 , 32 , 31 , 1/8 , 30 , 29,
#' 28 , 9/64 , 27 , 26 , 25 , 24,
#' 23 , 5/32 , 22 , 21 , 20 , 19,
#' 18 , 11/64 , 17 , 16 , 15 , 14,
#' 13 , 3/16 , 12 , 11 , 10 , 9,
#' 8 , 7 , 13/64 , 6 , 5 , 4,
#' 3 , 7/32 , 2 , 1 , A , 15/64,
#' B , C , D , 1/4 E, F , G,
#' 17/64 , H , I , J , K , 9/32,
#' L , M , 19/64 , N , 5/16 , O,
#' P , 21/64 , Q , R , 11/32 , S,
#' T , 23/64 , U , 3/8 , V , W,
#' 25/64 , X , Y , 13/32, Z , 27/64,
#' 7/16 , 29/64 , 15/32 , 31/64, 1/2 , 33/64,
#' 17/32 , 35/64 , 9/16 , 37/64, 19/32 , 39/64,
#' 5/8 , 41/64 , 21/32 , 43/64, 11/16 , 45/64,
#' 23/32 , 47/64 , 3/4 , 49/64, 25/32 , 51/64,
#' 13/16 , 53/64 , 27/32 , 55/64, 7/8 , 57/64,
#' 29/32 , 59/64 , 15/16 , 61/64, 31/32 , 63/64,
#' 1 , 1 3/64 , 1 7/64 , 1 1/8, 1 11/64, 1 7/32,
#' 1 1/4 , 1 19/64, 1 11/32, 1 3/8, 1 27/64, 1 1/2
#' )
#' TapSizeInch <- c(
#' , , , , , ,
#' , , , , , ,
#' , , , , , ,
#' , , , , , ,
#' , , , "0-80" , , ,
#' "1-64,1-72", , , , "2-56,2-64", ,
#' , , "3-48" , , "3-56" , ,
#' "4-40" , "4-48" , , , , ,
#' "5-40" , "5-44" , "6-32" , , , 0.1110 ,
#' "6-40" , , , , , "8-32,8-36",
#' , , , , "10-24" , 0.1520 ,
#' , , , "10-32" , , ,
#' , , , "12-24" , , "12-28" ,
#' , , , , , ,
#' , "1/4-20" , , , , ,
#' "1/4-28" , , , , , ,
#' , , , , "5/16-18" , ,
#' , , "5/16-24" , , , ,
#' , , , , "3/8-16" , ,
#' , , "3/8-24" , , , ,
#' , , "7/16-14" , , , ,
#' "7/16-20" , , , , , "1/2-13" ,
#' , "1/2-20" , , "9/16-12" , , "9/16-18" ,
#' "5/8-11" , , , "5/8-18" , , ,
#' , , "3/4-10" , , "3/4-16" , ,
#' , , , "7/8-9" , , ,
#' "7/8-14" , , , , "1-8" , ,
#' , "1-12" , "1-14" , , , "1 1/8-7" ,
#' , "1 1/8-12", "1 1/4-7" , , "1 1/4-12" , "1 3/8-6" ,
#' , "1 3/8-12", "1 1/2-6" , , "1 1/2-12" ,
#' )
#' InchTapDrills <- data.frame(Decimal,
#' Drills,
#' inchTapSize,
#' stringsAsFactors = FALSE)
#' }
#' @examples data(InchTapDrills)
#' str(InchTapDrills)
NULL
#' Starrett Metric Tap Drill Sizes
#'
#' A few numbers from \code{rnorm()}.
#' @docType data
#' @name MetricTapDrills
#' @format A numeric data frame.
#' @source Generated from \code{
#' ThreadSizeMetric <- c(
#' 1.6, 1.8, 2 , 2.2, 2.5, 3,
#' 3.5, 4 , 4.5, 5 , 6 , 7,
#' 8 , 8 , 10 , 10 , 12 , 12,
#' 14 , 14 , 16 , 16 , 18 , 18,
#' 20 , 20 , 22 , 22 , 24 , 24,
#' 27 , 27 , 30 , 30 , 33 , 33,
#' 36 , 36 , 39 , 39
#' )
#' ThreadPitchMeric <- (
#' 0.35, 0.35, 0.4 , 0.45, 0.45, 0.5 ,
#' 0.6 , 0.7 , 0.75, 0.8 , 1 , 1 ,
#' 1.25, 1 , 1.5 , 1.25, 1.75, 1.25,
#' 2 , 1.5 , 2 , 1.5 , 2.5 , 1.5 ,
#' 2.5 , 1.5 , 2.5 , 1.5 , 3 , 2 ,
#' 3 , 2 , 3.5 , 2 , 3.5, 2 ,
#' 4 , 3 , 4 , 3
#' )
#' TapDrillMetric <- (
#' 1.25, 1.45, 1.60, 1.75, 2.05, 2.50,
#' 2.90, 3.30, 3.70, 4.20, 5.00, 6.00,
#' 6.70, 7.00, 8.50, 8.70, 10.20, 10.80,
#' 12.00, 12.50, 14.00, 14.50, 15.50, 16.50,
#' 17.50, 18.50, 19.50, 20.50, 21.00, 22.00,
#' 24.00, 25.00, 26.50, 28.00, 29.50, 31.00,
#' 32.00, 33.00, 35.00, 36.00
#' )
#' TapDrillInch <- c(
#' 0.0492, 0.0571, 0.0630, 0.0689, 0.0807, 0.0984,
#' 0.1142, 0.1299, 0.1457, 0.1654, 0.1968, 0.2362,
#' 0.2638, 0.2756, 0.3346, 0.3425, 0.4016, 0.4252,
#' 0.4724, 0.4921, 0.5512, 0.5709, 0.6102, 0.6496,
#' 0.6890, 0.7283, 0.7677, 0.8071, 0.8268, 0.8661,
#' 0.9449, 0.9843, 1.0433, 1.1024, 1.1614, 1.2205,
#' 1.2598, 1.2992, 1.3780, 1.4173
#' )
#' MetricTapDrills <- data.frame(ThreadSizeMetric,
#' ThreadPitchMetric,
#' TapDrillMetric,
#' TapDrillInch,
#' stringsAsFactors = FALSE)
#' }
#' @examples data(InchTapDrills)
#' str(InchTapDrills)
NULL
#' Starrett Pipe Thread Tap Drill Sizes
#'
#' A few numbers from \code{rnorm()}.
#' @docType data
#' @name StarrettTapDrills
#' @format A numeric data frame.
#' @source Generated from \code{
#' DrillSize <- (
#' 11/32, 7/16 , 37/64, 23/32 , 59/64 , 1 5/32, 1 1/2,
#' 1 3/4, 2 7/32, 2 21/32, 3 1/4, 3 3/4, 4 1/4
#' )
#' ThreadSize <- c(
#' "1/8" , "1/4", "3/8" , "1/2", "3/4" , "1", "1 1/4",
#' "1 1/2", "2" , "2 1/2", "3" , "3 1/2", "4"
#' )
#' ThreadPitch <- c(
#' 27 , 18, 18 , 14, 14 , 11.5, 11.5,
#' 11.5, 11.5 , 8, 8 , 8, 8
#' )
#' PipeThreadDrill <- data.frame(Decimal,
#' Drills,
#' inchTapSize,
#' stringsAsFactors = FALSE)
#' }
#' @examples data(PipeThreadDrill)
#' str(PipeThreadDrill)
NULL
#' Cutting Speeds Table
#'
#' Cutting speeds for various materials
#' using a plain high speed steel cutter
#' @docType data
#' @name CuttingSpeeds
#' @format A numeric data frame.
#' @source Generated from \code{
#' Material <- c( "Steel (tough)",
#' "Mild Steel",
#' "Mild Steel (with colant)",
#' "Cast Iron",
#' "Alloy Steels (1320–9262)",
#' "Carbon Steels (C1008–C1095)",
#' "Free Cutting Steels (B1111–B1113 & C1108–C1213)",
#' "Stainless Steels (300 & 400 series)",
#' "Bronzes",
#' "Steel 12L14",
#' "Aluminium",
#' "Brass",
#' "Machinable Wax",
#' "Delrin",
#' "Polyethylene",
#' "Acrylic (with coolant)",
#' "Wood"
#' )
#' MPM.Min <- c(18, 3, 6, 1, 3, 4, 35, 23, 24, 9, 122, 90, 6, 11, 12, 15, 183)
#' MPM.Max <- c(50, 38, 7, 2, 20, 21, 69, 40, 45, 10, 305, 210, 6, 11, 12, 15, 305)
#' SFM.Min <- c(60, 10, 20, 6, 12, 10, 115, 30, 10, 30, 400, 300, 20, 35, 40, 50, 600)
#' SFM.Max <- c(100, 125, 25, 8, 65, 70, 225, 7, 80, 33, 1000, 700, 20, 35, 40, 50, 1000)
#'
#' cuttingSpeeds <- data.frame(Material, MPM.Min, MPM.Max, SFM.Min, SFM.Max, stringsAsFactors = FALSE)
#' }
#' @examples data(cuttingSpeeds)
#' str(cuttingSpeeds)
NULL
R Package Documentation
Browse R Packages
We want your feedback!
Note that we can't provide technical support on individual packages. You should contact the package authors for that.
Embedding an R snippet on your website
Add the following code to your website.
For more information on customizing the embed code, read Embedding Snippets.